Difference between revisions of "Howto:Build and run FlightGear on Raspberry Pi 4"

From FlightGear wiki
Jump to navigation Jump to search
Line 310: Line 310:
There are also inexpensive heat sink kits.  Some opt for no after market cooling options at all, however it has been reported the the Pi4 will self cool the best when placed/mounter in the vertical direction.
There are also inexpensive heat sink kits.  Some opt for no after market cooling options at all, however it has been reported the the Pi4 will self cool the best when placed/mounter in the vertical direction.
===SD Card===
For casual running of FlightGear, a quality SD card works well. Look for Class A1 cards. The 'A' is for applications. In addition to a write speed of 10MB/s, these support at least 1500 read operations and 500 write operations per second. Do not use cheap fake SD cards. Interestingly, there is a new tool to test your SD cards. This new tool is called agnostics and can be installed with the below commands:
<syntaxhighlight lang="bash">
sudo apt update
sudo apt install agnostics
What device does it test?
Simon Long wrote (from the below link)
It tests whatever device currently containst the directory /var/tmp. If you want to test another device, modify the relevant line in sd_bench.fio to select a directory on the device you want to test.
To learn much more about the SD cards and agnostics, see the below link:
[https://www.raspberrypi.org/blog/sd-card-speed-test/ SD Card Speed Test]
====SD Card Speed Test====
{| class="wikitable"
! SD Card !! Bar Code !! SWS KB/sec !! RWS IOPS !! RRS IOPS !! Comment
| SP Superior Pro 64GB || X0026RJ70Z || 38986 || 1067 || 3344 || Used for ~ 1 month
| Example || Example || Example || Example || Example || Example
| Example || Example || Example || Example || Example || Example
===Hard Drives===
{{not done}}
[[Category:Raspberry Pi]]
[[Category:Raspberry Pi]]
[[Category:Building from source‎]]
[[Category:Building from source‎]]

Revision as of 00:28, 5 January 2021

It is now possible to run FlightGear on a Raspberry Pi, starting with the model Pi 4. The objective of Howto:Build and run FlightGear on Raspberry Pi 4 is to introduce Pi users to FlightGear and possibly FlightGear users to the Raspberry Pi family. One of the main objectives of the Raspberry Pi is education. Hopefully this marriage will introduce some young programmers to FlightGear. Although this will mainly deal with the Pi 4, other models may find applications in the area of flight panels and instruments.


Update Raspbian

Use the below commands to update your Raspberry Pi:

sudo apt-get update
sudo apt-get full-upgrade

Do not use the below update command unless you know how and why to use it. This command will install experimental software that has a good chance of breaking your operating system. It is like flying into a thunder storm cloud.

sudo rpi-update          (DO NOT USE)

Backtrace using gdb: and Download_and_compile.sh

Tracking down a crash with double free corruption (fasttop)

Set environment variable:

set environment MALLOC_CHECK_ 2

Next run FlightGear with debug:

./run_fgfs_debug.sh --launcher

Use the below gdb commands handle SIGPIPE nostop and handle SIG32 nostop to skip innocent events:

gdb: handle SIGPIPE nostop
gdb: handle SIG32 nostop

Use r within gdb to run FlightGear:

gdb: r

After the crash use the gdb command bt to print the backtrace:

gdb: bt


Using the command line osgviewer to display models. These instructions are for FlightGear and OSG built with download_and_compile.sh.

cd /flightgear/dnc-managed/install/openscenegraph/bin

export LD_LIBRARY_PATH=../openscenegraph/lib:$LD_LIBRARY_PATH

./osgviewer "path to your model file"

Type h for the help menu.

Feature Scaling - FlightGear

Menu Bar

Hiding the menu bar improves FPS too some degree. More so when FlightGear is running in a window. It can be toggled on/off with [Shift] + [F10] or the Auto Hide option can be used.

GPU Profile

1rightarrow.png See Graphics card profiles for the main article about this subject.

The following GPU profile was provided by enrogue [1]

<?xml version="1.0"?>

    <custom-settings type="bool">true</custom-settings>
    <clouds type="double">0</clouds>
    <generic type="double">1</generic>
    <landmass type="double">3</landmass>
    <model type="double">0</model>
    <contrails type="double">1</contrails>
    <crop type="double">0</crop>
    <skydome type="bool">false</skydome>
    <transition type="double">0</transition>
    <urban type="double">0</urban>
    <water type="double">3</water>
    <wind-effects type="double">0</wind-effects>
    <vegetation-effects type="double">0</vegetation-effects>
    <forest type="double">0</forest>
    <lights type="double">3</lights>
    <quality-level-internal type="double">3</quality-level-internal>
    <quality-level type="double">-1</quality-level>
  <random-objects type="bool">true</random-objects>
  <random-vegetation type="bool">true</random-vegetation>
  <random-vegetation-shadows type="bool">false</random-vegetation-shadows>
  <random-vegetation-normals type="bool">false</random-vegetation-normals>
  <vegetation-density type="double">1</vegetation-density>
  <random-buildings type="bool">false</random-buildings>
  <building-density type="double">1</building-density>
  <point-sprites type="bool">true</point-sprites>
  <particles type="bool">true</particles>
  <clouds3d-enable type="bool">true</clouds3d-enable>
  <clouds3d-vis-range type="double">10000</clouds3d-vis-range>
  <clouds3d-detail-range type="double">10000</clouds3d-detail-range>
  <clouds3d-density type="double">0.25</clouds3d-density>
    <enabled type="bool">true</enabled>


1rightarrow.png See FG1000 for the main article about this subject.

For the time being, the FG1000 must be considered hardly usable on the RPi, i.e. ~200ms/5fps. We're currently in the process of investigating what can be done to make it possible to use the device on the RPi, since that would seem like a perfect use-case.

One thing that's obvious is that initialization of the device takes unusually long. To see what's going on, we can wrap the initialization code inside $FG_ROOT/gui/menubar.xml in between profiling calls:

diff --git a/gui/menubar.xml b/gui/menubar.xml
index ff3faa1ac..6c94b2e76 100644
--- a/gui/menubar.xml
+++ b/gui/menubar.xml
@@ -834,6 +834,7 @@
+                                       fgcommand("profiler-start");
                                        var nasal_dir = getprop("/sim/fg-root") ~ "/Aircraft/Instruments-3d/FG1000/Nasal/";
                                        if (! defined("fg1000")) {
                                                io.load_nasal(nasal_dir ~ 'FG1000.nas', "fg1000");
@@ -846,6 +847,7 @@
                                        var fg1000system = fg1000.FG1000.getOrCreateInstance();
                                        var pfdindex = fg1000system.addPFD();
+                                       fgcommand("profiler-stop");

Another thing worth trying is running the built-on OSG optimizer on the root group, this requires patching SG/FG respectively:

diff --git a/simgear/canvas/elements/CanvasGroup.hxx b/simgear/canvas/elements/CanvasGroup.hxx
index 33687637..288da23d 100644
--- a/simgear/canvas/elements/CanvasGroup.hxx
+++ b/simgear/canvas/elements/CanvasGroup.hxx
@@ -20,6 +20,8 @@
+#include <osgUtil/Optimizer>
 #include "CanvasElement.hxx"
 #include <list>
@@ -97,6 +99,11 @@ namespace canvas
       getTransformedBounds(const osg::Matrix& m) const override;
+      void optimize () {
+             osgUtil::Optimizer opt;
+             opt.optimize(_scene_group.get()  );
+      }
       static ElementFactories   _child_factories;
diff --git a/src/Scripting/NasalCanvas.cxx b/src/Scripting/NasalCanvas.cxx
index 602f06989..23aadfb36 100644
--- a/src/Scripting/NasalCanvas.cxx
+++ b/src/Scripting/NasalCanvas.cxx
@@ -521,7 +521,8 @@ naRef initNasalCanvas(naRef globals, naContext c)
     .method("_createChild", &f_groupCreateChild)
     .method( "_getChild", &f_groupGetChild)
-    .method("_getElementById", &sc::Group::getElementById);
+    .method("_getElementById", &sc::Group::getElementById)
+    .method("optimize", &sc::Group::optimize);
     .method("heightForWidth", &sc::Text::heightForWidth)

Feature Scaling - Raspberry Pi OS

Screen Resolution

Raspberry Pi screen layout editor for adjusting screen resolution.

When running FlightGear, using the full screen option, 1024 X 768 resolution works well. Possibly because this is FlightGear's native resolution. In order to choose this resolution go to the Raspbian program menu 'Preferences' and run 'Screen Configuration'. Now right click on the screen that needs to be adjusted to 1024 X 768, on the Screen Layout Editor seen to the right. If using two screens, it might be best to set both screens to the same resolution. Also, it is best to have the two HDMI boxes touching so that the mouse cursor doesn't have a dead spot. Click on the green check to finish.

Memory split

The memory split option is found in the raspi-config program, under "7 Advanced Options."

sudo raspi-config

This option adjusts gpu_mem and thus allots the GPU memory. Starting with the Pi4, most of the GPU memory is controlled by the the Linux kernal and there is a disadvantage when gpu_mem is set too high. Never exceed 512MB, less is better. vcgencmd get_mem gpu will report GPU memory set by gpu_mem.

For more information see Memory options in config.txt


Expanding the flight simulator system beyond the primary Raspberry Pi4, that is running FlightGear, is one way to increase the computing power of such a small computer.


Avare connected to the Raspberry Pi4 and FlightGear. Avare is a moving aviation chart app.

Avare is a free aviation app, with no ads, that works well with FlightGear. It is an app that is used by many pilots. It will provide a moving map of the FlightGear aircraft, using all FAA charts and a lot more. These charts are for the USA, however some of these FAA Charts cover Puerto Rico, plus parts of Canada, Mexico and the Caribbean. For other parts of the world, there are other apps that might work. Avare can be downloaded from Google Play Store. A tablet is a good choice for running this app.

FlightGear and Avare are easy to bind together. Along with the main Avare app, the I/O app will also need to be installed on the tablet. This app is ‘Avare External I/O Plugin’. The scheme is that the Raspberry Pi4 and FlightGear will become the GPS signal used by the Avare app, this position is transferred via WiFi. So, the tablets internal GPS needs to be OFF. Avare will always prompt you to turn ON the internal GPS, so when asked to ‘Turn On GPS’, choose ‘No’. In ‘Preferances’ the GPS position source can and should be set to ‘Avare IO Module Only’, however the prompt to turn ON the internal GPS will still pop up when starting the app.

The below command tells FlightGear what to connect to and it's protocol. This can be placed in the GFly type programs or if in Terminal, place the command after fgfs. The address, 192.168.??.?, needs to be the address of the tablet running Avare. Some home networks will randomly choose an address, hence this could change. It will be displayed in the IO app. The number 49002 needs to be the same number that is in the Avare IO app. Use the Xplane option.

Comm Comm Type Direction Hertz Machine Address Port Style Protocol
--generic socket out 2 192.168.??.?? 49002 udp avare

The table above helps to explain the command line below.


After FlightGear has started with the above command, open the Avare External I/O Plugin app. Choose the Xplane option and then tap on ‘Listen’. There should be lines of communication being displayed after ‘Listen’ is enabled. Leave this running and now open the main Avare app. Do not choose to use the internal GPS. Now your FlightGear aircraft placement should be displayed on the FAA map of choice.

Official 7" Touch Screen

The Official 7" Touch Screen for the Raspberry Pi with an external numeric keypad.
Bottom view of the 7" touch screen for the Raspberry Pi.
The Phi PFD displayed on the official Raspberry Pi touch screen.

There is the Official 7” Touch Screen for the Raspberry Pi. This screen will work with a number of different models of the Raspberry Pi’s. There is a case for it (there is no Official case) and the Pi, however the new Pi4 doesn’t fit this case, seen in the photo at the right. This combination does resemble a modern aircraft instrument. There is a new case that will fit the Pi4 and other models, SmartPi Touch 2.

SmartPi Touch 2

Phi will work with almost any device with a browser. In this example the Touch Screen is used with a Raspberry Pi3 B+. There is a screen touch keyboard, however only the numeric keyboard is needed to operate the Radio Stack and the full keyboard doesn’t make efficient use of the screen area. To the right, an external numeric keypad is being used. It makes an interesting combination to touch on screen hot spots and use the external keyboard to input the radio frequencies. A numeric touch screen keypad is being looked into.

Pass the below command to FlightGear, during startup, using your favorite method:


In the browser address bar, the one with the 7” Touch Screen, type the below address. Replace the '??' with your numbers. This address needs to be the address of the Raspberry Pi4 that is running FlightGear. Some home networks randomly assign addresses, so when launching FlightGear it is good practice to check the address. To easily find this address, place the mouse cursor on the WiFi/Network icon that is on the top menu bar. It is to the far right.


In order to adjust the screen brightness use the below command to write a value into the brightness file. Adjusting the number ‘128’ to a lower value will reduce the brightness of the screen.

sudo sh -c ‘echo “128”>/sys/class/backlight/rpi_backlight/brightness’

Other, less expensive, models of Raspberry Pi’s should also work. As long as it has the port for the Official Touch Screen and can run a browser. There are also third party touch screens on the market. However, purchasing official Raspberry products help to support the Raspberry Foundation promote computer education. Hopefully some of the young budding computer scientists will find value in FlightGear!

64-bit operating system

The Raspberry Pi4 can run FlightGear with a 64-bit OS.

Ubuntu Server

Unofficial distribution of Ubuntu Server 18.04.4 for Raspberry Pi 4.

FlightGear PPA for Raspberry Pi 4.


Noctua cooling fan used to cool the Raspberry Pi4 while running FlightGear.

The video core GPU temperature can be read with the use of the terminal and the below command:

vcgencmd measure_temp

The Raspberry Pi4 starts to throttle at 80c, and will be fully throttled when it hits 85. When flying the DC-3 Dakota at a steady cruse altitude, in a low scenery dense area, the core temperature was reported to be ~75c. This was with ambient temperature of ~24c. The temperature rapidly dropped to ~45c when the cooling fan was energized. There was no heat sink installed for this test. FlightGear was running in fullscreen mode on monitor 1 and terminal was running on monitor 2. Screen resolution was possibly 1024 x 768.

The fan in the photo is a Noctua NF-A4x10 5V. It is installed with two rubber bands forming an X. Then the fan is simply sandwiched in the middle of the X. The ends of the rubber bands are looped over the ends of the four standoffs. The rubber bands, in addition to holding the fan, help to isolate vibrational noise. In this setup the fan was powered by an orphaned cell phone charger.

There are also inexpensive heat sink kits. Some opt for no after market cooling options at all, however it has been reported the the Pi4 will self cool the best when placed/mounter in the vertical direction.