8,564
edits
Howto:Build and run FlightGear on Raspberry Pi 4: Difference between revisions
Jump to navigation
Jump to search
Howto:Build and run FlightGear on Raspberry Pi 4 (view source)
Revision as of 08:09, 24 February 2020
, 24 February 2020Create subheadings by adding one or more = symbols (preferred over HTML tags). Added some wiki links
(Create subheadings by adding one or more = symbols (preferred over HTML tags). Added some wiki links) |
|||
| Line 1: | Line 1: | ||
== Joysticks == | == Joysticks == | ||
You will find that controlling your aircraft, with the official Raspberry Pi keyboard and mouse, too be rather difficult. A joystick will solve this problem. The Logitech Extreme 3D PRO is plug and play, for the most part, with FlightGear. Most modern joysticks should also work. There is a dialog box to assign common joystick controls, in FlightGear. Controls are also properties, however that is for later. This joystick dialog box is found in the top menu bar under 'Files'. Next you will find 'Joystick Configuration' to click on and that will bring up the desired dialog box. | You will find that controlling your [[aircraft]], with the official Raspberry Pi keyboard and mouse, too be rather difficult. A [[Input device|joystick]] will solve this problem. The Logitech Extreme 3D PRO is plug and play, for the most part, with [[FlightGear]]. Most modern joysticks should also work. There is a dialog box to assign common joystick controls, in FlightGear. Controls are also properties, however that is for later. This joystick dialog box is found in the top menu bar under 'Files'. Next you will find 'Joystick Configuration' to click on and that will bring up the desired dialog box. | ||
If the joystick’s travel is not being used efficiently or the neutral dead band is not right, the joystick can be calibrated. Install jstest-gtk through the Raspbian software installer or use the terminal and apt-get install command. | If the joystick’s travel is not being used efficiently or the neutral dead band is not right, the joystick can be calibrated. Install jstest-gtk through the Raspbian software installer or use the terminal and apt-get install command. | ||
| Line 61: | Line 61: | ||
[[File:Jstest-gtk Joystick Calibration.jpg|thumb|Joystick calibration using jstest-gtk dialog box.]] | [[File:Jstest-gtk Joystick Calibration.jpg|thumb|Joystick calibration using jstest-gtk dialog box.]] | ||
=== Saitek Saitek Pro Flight Quadrant === | |||
This throttle quadrant is now produced by Logitech and works with FG and the Raspberry Pi4. If used with a single engine aircraft or a multi engine aircraft where the engines are controlled with one stick on the quadrant, this will be a plug and play setup. However, there will be a noticeable dead band in the middle of the travel. Furthermore, it is possible that all the usable stick travel is not utilized. Both of these issues can be addressed by calibrating the quadrant as in the joystick example above. Below is the calibration data before calibration and below that is the data after calibration. Notice that the center dead band is removed. | This throttle quadrant is now produced by Logitech and works with FG and the Raspberry Pi4. If used with a single engine aircraft or a multi engine aircraft where the engines are controlled with one stick on the quadrant, this will be a plug and play setup. However, there will be a noticeable dead band in the middle of the travel. Furthermore, it is possible that all the usable stick travel is not utilized. Both of these issues can be addressed by calibrating the quadrant as in the joystick example above. Below is the calibration data before calibration and below that is the data after calibration. Notice that the center dead band is removed. | ||
| Line 123: | Line 122: | ||
</syntaxhighlight> | </syntaxhighlight> | ||
=== Thrustmaster Flight Rudder Pedals === | |||
There could be two adjustments needed for these rudder pedals. The toe brakes are reversed and delete the toe brake center dead band. Use the same method to delete the dead band as in the above throttle quadrant. Do not delete the dead band for the rudder unless that is what you want to do. Below is a calibration data example: | There could be two adjustments needed for these rudder pedals. The toe brakes are reversed and delete the toe brake center dead band. Use the same method to delete the dead band as in the above throttle quadrant. Do not delete the dead band for the rudder unless that is what you want to do. Below is a calibration data example: | ||