Animated jetways are dynamic models that connect to your aircraft when you are pulled up at a gate. FlightGear boasts the most advanced animated jetways in the flight simulator market, beating those of Microsoft Flight Simulator and X-Plane in features — a testament to the flexibility of FlightGear. This article describes how to obtain and use the jetways and interface them with aircraft and scenery.
- 1 Current state
- 2 Obtaining and installing
- 3 Using the jetways
- 4 Adding support in aircraft
- 5 Adding support in scenery
- 6 Future Development
- 7 Related content
As of September 2015, only the following airports have animated jetways.
- London Gatwick Airport (EGKK)*
- Amsterdam Airport Schiphol (EHAM)
- Denver International Airport (KDEN)*
- Las Vegas McCarran International Airport (KLAS)*
- San Francisco International Airport (KSFO)
- Ted Stevens Anchorage International Airport (PANC)*
* indicates the jetways for this airport were auto-converted and do not have gate numbers.
The generic jetway model in FGData is broken, but there is a repaired version in the TerraSync scenery repository.
Obtaining and installing
FlightGear 2.4.0 and later include the animated jetway system. Nothing extra has to be installed.
Using the jetways
- Start FlightGear in any animated jetway-compatible aircraft. As of May 2016, these include the following:
- Fly (or spawn) to any airport equipped with animated jetways. You can tell if a jetway is animated by pressing Ctrl+C; if the polygons are highlighted in yellow, then it is animated.
|Note Ensure you have the latest scenery from TerraSync so you do not get conflicts between animated and static jetways.|
- Taxi up to an animated jetway and park near it, then click it. If your aircraft is supported and parked well enough, the jetway will extend, rotate, and connect.
Adding support in aircraft
- Open up the main model of your aircraft in your favorite 3D modeling software (such as Blender).
- Move the model around to account for any offsets you have in the main model file, then get the coordinates of the door.
- Add the following code in your aircraft's -set.xml (remember to merge the tags properly):
<sim> <model> <door> <position-x-m type="float">X-M</position-x-m> <position-y-m type="float">Y-M</position-y-m> <position-z-m type="float">Z-M</position-z-m> <jetway-hood-deg type="float">HOOD-DEG</jetway-hood-deg> </door> </model> </sim>
- where X-M, Y-M, and Z-M are the X/Y/Z coordinates of the door in meters and HOOD-DEG is the jetway hood rotation amount. To specify more doors, just add more door elements.
- Add the following code into your XML model file to enable the jetways to connect to your aircraft over the multiplayer network:
<nasal> <load> var model = cmdarg(); model.getNode("door/position-x-m", 1).setValue(X-M); model.getNode("door/position-y-m", 1).setValue(Y-M); model.getNode("door/position-z-m", 1).setValue(Z-M); model.getNode("door/jetway-hood-deg", 1).setValue(HOOD-DEG); </load> </nasal>
- Again, replace X-M, Y-M, Z-M and HOOD-DEG with their respective values. To add more doors, duplicate the last four lines of Nasal code and replace  with  or .
Adding support in AI aircraft
Follow the steps for regular aircraft above, but only add in the Nasal code.
jetway-enabled AI Aircraft (9/2015)
AI/Aircraft/A319/A319-main.xml AI/Aircraft/A320/A320-main.xml AI/Aircraft/737/737-main.xml AI/Aircraft/MD80/MD80-main.xml AI/Aircraft/A321/A321-main.xml AI/Aircraft/747-400/747-400-main.xml
Adding support in scenery
Launch FlightGear in your favorite aircraft. The author uses the Bluebird. You cannot use the UFO because its scenery-editing function will interfere with the jetway editor. Go to AI > Jetway Settings and tick the "Enable jetway editor" checkbox. Then click the "Open Editor" button.
With the editor enabled, click anywhere on the ground to place an animated jetway, which will flash to indicate it is selected. The jetway editor is similar to the UFO's scenery model editor. You can Alt-click on the terrain to move the current selected jetway. Ctrl-click selects the jetway closest to the click position (the new jetway will flash to indicate it's selected). Shift-click deselects the current jetway.
The dialog is used to adjust the selected jetway. The top sliders adjust position and orientation, and the bottom ones adjust the jetway itself. The offsets that the bottom sliders control can be used to model jetways that are in obscure configurations. The drop-down menus at the very bottom of the dialog control various properties of the jetway, such as the model, gate number, airline sign, and door number. At the moment, the following models are available:
When you are finished editing your airport jetway layout, click the "Export" button. A jetway definition file will be created and written to $FG_HOME/Export/ICAO.xml, where ICAO is the ICAO code of the nearest airport. (The exact location of this file is printed to the console window.) This file should be submitted to Terrasync (see FlightGear Scenery Database#Contribute).
Auto-converting static/obsolete jetways
| Work in progress|
This article or section will be worked on in the upcoming hours or days.
See for the latest developments.